Real Fiero Tech

HAHAHA Hitler taught our country a lot about Attacking your own and saying it was someone else.

Nah you can keep your car. Might keep you from walking one day. Never noticed in any posts that they were sold. Should edit that first post a bit I guess. Anyway I have an excuse. I'm freaking exhausted.

Arron is the susp stuff gone? If not what do you want for it?

As a TOP GEAR fan that is one of the best so far. Other than the Toyota Challenge.

Hmm AMC EAGLES. Have to check on that. But if that's the case they probibly don't make the material any more since there's not any more need in it.

POSTED BY IMSA GT on Old Europe Since there has been quite an uproar over the dew wipes that are now available from member DIY_Stu and the Fiero Store, I decided to do a review on both manufacturers. I was fortunate enough to acquire a set of Stu's dew wipes the other day and also a set from the Fie...

I can't give discounts. The quality is far worth the price. These are hand made. If you estimate the price minus cost to make then I earn less than $8 an hour making these things. They literally take a lot of my time. I don't watch TV because it slows my work. try not to be on the computer much. and...

Not a chance in hell. These are 100% hand made. Hell I would allow friends to help because I'm so picky about them being as perfect as they can be. Nothing but Praises. I can't punch out the quantity that TFS wants so they enlisted the Chinese to make them. All their brackets have round holes instea...

SETS OF OUTER DEW WIPES IN STOCK http://www.diyfiero.com/dropspot/wipes.gif ................................ I'm selling sets of hand made inner and outer dew wipes. OUTER DEW WIPES I installed my trial pair (first set made) on my personal 87GT. They fit great. These are made using the correct rivet...

I've used it several times in the past without a hitch, assisted my neighbor with the stuff and his truck hasn't stopped smoking for the last year. Moral to the story. If gunk is keeping it from leaking..... it won't any more. He used it in fuel, oil, and we used it direct through the throttle body.

The guy that I'm doing the 5speed wiring for received a call from Loyde today. He was asked if he was going to buy one of his swap harnesses and computers. When he said no he says Loyde started getting upset with him and started cussing at him and saying that it won't run good, and how no one can pr...

Also need to know how much for a chip burn.

Will, could you put together a supplies list for tuning? I'm looking to Emulate then once that's done I'll need to burn the new chip for finalizing the install. This will be done on OBD1 3800sc and Syclone or Turbo Sunbird ECM 16198263.

What spoofs are needed for OBD1? I know on my wife's car She wants an auto so OBDII may be the best way to go on that since I already have the 4T65E-HD. How much does Sinister charge for the OBDII programming? It will be a straight up No mods install which should make it easy since it'll only need P...

Fierox runs a t-66 on his.

It's been said (by loyde) that OBD2 is way better than 1 and you will lose power with OBD1 on an OBD2 engine. I doubt it but when Wideband tuning you may get a flatter line with 2 I think. But I'll leave it to the experienced to tell. I know Sinister has the OBD2 tunercat tuning software before it w...

Looking at going with Sinister for programming but still undecided on which computer to run. Have a 96 PCM right now but have access to a 93 ECM. Wiring will be done by me. Are any of these still suffering from stalling during shifts? Any and all info would be great. But I do need to get wiring soon...

:thumbleft:

My measurements are 3" CTC crank holes and the rest match yours. You state that it's 3 1/8 to the best you can measure. Measuring from outer edge to inner edge is the same as CTC. But I think we found a $57 replacement to a $200 Street Dreams part. Just saved me some money. Not to see if I can ...

still have that flexplate accessible? If so could you get me the measurements off of it?

Crank hole pattern center to center of oposing holes
Total diameter
distance from one TC hole to the next.

Shouldn't this be in advanced?

Great observation on the flexplate.