Real Fiero Tech

Wow some of you guys are real douche bags eh? We sorted out the problems in the end. Turns out Brunton didnt change the VSS to read the Fieros signal and it cause the high idle and stalling. The 2nd listing didnt need to be as high since the first guy gave a nice deposit and then backed out. Needles...

Actually before you start ripping into people you should wait and see what the problems are. We found that I somehow forgot to plug in the front 02 sensor while adding plug wires! Sweet! I knocked the vac line off the MAP as well. We got those sorted and the car starts and idles fine 60% of the time...

Codes:
P0753
P0123
P0132
P0502
P0121
P0140
P0530
P1673

Trunk release does go throught the C500, B1 IIRC. Not according to the '88 shop manual. The solenoid power comes from the CTSY/LID fuse, goes through the switch and the secondary of a relay. The relay primary is energized by the parking brake switch in manual cars and the transmission range selecto...

Trunk release does go throught the C500, B1 IIRC.

Dark, the PCM was tuned by Brunton Automotive, they are the makers of the Stalkerv6 kit car here in Fl. I was quoted to have about 250-260whp. It starting to feel that way once I put good fuel in it.

Did a little diagnostic work but nothing solved the high idle problem. Swapped 3 different TPS- all ranged to 4.5v full throttle but the lowest at closed was .98v. Swapped MAF- no change Swapped original PCM- no change Wiggled wire at C500 and the trunk release worked for a bit- HMmmm may be on to s...

Just a few things to sort about the harness. Jim didnt pin the CEL so I have to go in and add a wire. He is used to making Ed Parks 4.9 harness and they leave the CEL out for some reason. Also my trunk release has stopped working. I can hear the relay under the dash click but nothing happens. I need...

For the idle problem: The ECM will not command the IAC until it sees 0% throttle position from the TPS. The ECM determines where 0% throttle is by recording the LOWEST voltage it has seen from the TPS that isn't 0.00volts. The highest voltage it has seen is also recorded, and this is 100% throttle....

Nah I am going to leave the bumper as is. I am going to make a heat shield and fill the bottom of the trunk. To do list: I need to get the A/C hose made and the system charged Have the alignment checked Fix the manifold to exhaust pipe leak Find out the engine wants to idle at 3k until until you unp...

Some people dont quite understand offset and how a wheel will set in relation to the body. On the ET the HIGHER the number the more the wheel will be "sunk" into the body. The lower the number, the further it will be pushed AWAY from the car. I was told a 17x8 ET45 & 18x8 ET35 would st...

Ok here are some of the pre clean up pics as well as the final "to do" list. We had to cut the bottom of the trunk out to clear the 3" inch exhaust. I wasnt too happy about this but what can ya do? We also used some of the original coolant system hard pipes in order to use as little c...

Thanks. You need to turn the wheel straight though. Those pics don't help.. Due to the scrub radius, they will get pushed out as you turn the wheel left. Notice they stick out from the front part of the fender? The whole wheel will stick out a bit when turned straight. Or are you just running a LOT...

Thanks. You need to turn the wheel straight though. Those pics don't help.. Due to the scrub radius, they will get pushed out as you turn the wheel left. Notice they stick out from the front part of the fender? The whole wheel will stick out a bit when turned straight. Or are you just running a LOT...

Yet you still fail to show a picture that lets us see how the wheel fits in relation to the fender. News flash: Your Evo, and especially its horsepower claim, have absolutely nothing to do with Fiero wheels. But hey, if it makes you feel like a big boy... An angle like this shows how the wheels are...

Uhhhh my fronts are 17x8 with a 45et and they dont stick out past the fenders. Its an 88 as well. <useless side picture of car that shows nothing related to offsets> How does a side view show anything about how the wheel sits in relation to the fender? Maybe you should post a view from the front. I...

Uhhhh my fronts are 17x8 with a 45et and they dont stick out past the fenders. Its an 88 as well. http://i17.photobucket.com/albums/b86/BVM03/Fiero/Fiero010.jpg How does a side view show anything about how the wheel sits in relation to the fender? Maybe you should post a view from the front. If you...

Yeah those are an Enkei design. "Enkei" is cast into the wheel. They use the same design on the wheels they make for Formula 1. Here's the F1 version: http://farm4.static.flickr.com/3064/2545399949_7cc0f64677.jpg?v=0 I love the style. I was considering buying some but they don't have the ...

Yeah those are an Enkei design. "Enkei" is cast into the wheel. They use the same design on the wheels they make for Formula 1. Here's the F1 version: http://farm4.static.flickr.com/3064/2545399949_7cc0f64677.jpg?v=0 I love the style. I was considering buying some but they don't have the ...

Yep thats me... fuckin scary you found that old post. :thumbleft: First one was my 1995 NISMO stage1 R33 GTR vspec. Second was actually my first skyline and its a 1991 R32 GTS-t. Now here is the part you are really gonna think is crazy. I used to have so much fun drifting the R32 that I preferred to...