Real Fiero Tech

not a ton of progress, but I made a fuel sending unit top, there will be fittings for supply, return, a tank vent, and electrical connections. supply and vent will be -10, return will be -8. I'll nickel plate the assembly once it's a bit further along. https://i.imgur.com/6XsFSyn.jpg https://i.imgur...

I've been running a small battery on the car for years, I understand it's limitations, it's not a problem.

Thanks for the follow up, I'll have to make some revisions. I think slots might be the smart answer, to allow for some adjustability for transmission placement. I'm been extremely busy working on my house, and haven't had much time to do many of the things I would like to do, like work on these and ...

I've never had a problem, but I also haven't been in a situation where I needed to crank for a long time, and I acknowledged it would be a potential limitation.

the dyna batt died, admittedly, I let it freeze and go without any load cycles for several months, and they are sensitive to deep discharge. years ago, I found this link which suggested the dynabatt was just a rebranded battery from another manufacturer https://stealth316.com/2-dynabatt.htm I didn't...

some quick googling looks like the Voron is a custom build it yourself printer? looks very well built from what I can see. I need to get my printer out and dusted off, but I could also use to make some significant upgrades to it as well, unfortunately, that will have to wait until I get this dump of...

So, i have pulled the pedal box before, my car was born an automatic, I wonder how much stiffness can be added by a flat plate, to me, it doesn't look like the issue is as localized as that portion of the firewall, but the whole firewall. Maybe I'm wrong though.

I'm super curious about how your firewall panel will look, and how it will perform. I have an idea in my head to reinforce that area as well, but it's much different than a panel, I also haven't even started working on the design though.

so, a few updates. I got the master bedroom wiring mostly finished, later this week, I'm going to try and get most of the other circuits landed in the breaker panel and run to their respective areas, I also removed the window that was on the wall, in what it now going to be the master bathroom. http...

For a while, I had considered the earlier sunfire headlights for a pop-up delete, if I were feeling like completely re-sculpting my entire front end. that looks like a clean example!

are the clips you're using to hold the speed sensor cable to the brake line 3d printed? how are your prints holding up in environments like that? care to give us a run down on your printer and process? I 3d printed some hubcap adapters for my car at one point, but they warped in the heat here in SC....

The Crower's are solid lifters, they may work, but I would prefer to run a hydraulic lifter if I can. Crower does list lifter parts on their website, which may help me get a set of link bars and replacement pins/washers for them, if they fit. I suspect they will fit, because several cam companies se...

Second, might want to build the VSS, and back up light harness with a connector so it can be be divorced from the main harness, and adapted to other transmissions. I'm not at all above re-terminating or splicing onto those wires when I switch to the F40. Good point, though. I should be considering ...

I don’t really like the corner counterspace next to the fridge; looks like it is obstructed and hard to use. Can you put the pantry in that corner? Maybe not possible with the vent area… I hadn't really considered it that way, but you're very right, I hadn't considered that the fridge was full heig...

Silly me for thinking R was refrigerator it's alphabetical, "Range" comes before "refrigerator" I made some revisions, it works out to about 13x11 for the "kitchen" although the kitchen is open to the rest of the space, which is about 13'x36' https://i.imgur.com/WFb15R...

Some thoughts: Plenum concept would ensure equal pressure to each duct, but each duct has a different length, number of turns, etc, so it doesn't mean that the resulting flow would be the same. And depending on the rooms, they may not all need the same cfms, so I wouldn't get too worked up over thi...

Unfortunately, what is described above was significantly more than a day's work.

First, Japan is rad, I would love to go check it out again, especially as a civilian.

Second, might want to build the VSS, and back up light harness with a connector so it can be be divorced from the main harness, and adapted to other transmissions.

so, I've made a significant change to what I was going to do with the house, I decided not rebuild the "patio" space, as it would just cost too much money to properly enclose. probably won't be a ton of pictures, as most of the work is kinda hard to capture in a picture right now, when it'...

I'll have to look into the element analysis, I'm not sure how well it would work with the way I design my parts, but that's a great reason to change the way I design parts. I'm on design 3 of the alternator mount, I'm onto a design that I believe to be viable, but I would like to integrate a dog bon...