Storm Trooper Maintenance Thread
Moderators: The Dark Side of Will, Series8217
-
- Peer Mediator
- Posts: 15679
- Joined: Wed Nov 24, 2004 11:13 pm
- Location: In the darkness, where fear and knowing are one
- Contact:
Re: Storm Trooper Maintenance Thread
The lower ball joint taper in the knuckle was messed up; I didn't notice this when I put new lower ball joints in it last summer... here comes another lower ball joint. I pulled a knuckle out of "the stash" that looks better. I'll talk to my prototype machinist about snagging a 2in/ft tapered reamer and see about repairing the current one, but need the car on the road sooner than that.
-
- Peer Mediator
- Posts: 15679
- Joined: Wed Nov 24, 2004 11:13 pm
- Location: In the darkness, where fear and knowing are one
- Contact:
Re: Storm Trooper Maintenance Thread
'88 upper ball joint taper is 10 degreesThe Dark Side of Will wrote: ↑Wed Feb 26, 2020 8:54 am The 1988 Fiero lower ball joint taper appears to be 2 inches per foot (~4.75 degrees half-angle), which is kind of weird. Now to find a 2in/ft tapered reamer to fix the lower ball joint taper in my right knuckle...
-
- Peer Mediator
- Posts: 15679
- Joined: Wed Nov 24, 2004 11:13 pm
- Location: In the darkness, where fear and knowing are one
- Contact:
Re: Storm Trooper Maintenance Thread
The flats on Rodney Dickman's "zero lash" sway bar end links are significantly too narrow for a normal wrench.
Enter the way too complicated solution:
Send-Cut-Send has a minimum order, so once we got their system to interpret my .DXF correctly (They use R12 .DXF... WTF?) they sent me 11 to fulfill minimum order cost.
And in action
I spread one trying to get the nut under the control arm tight. I guess it's good they sent me 11. I'm not sure there's room to make one that won't spread... maybe I'll play with it on a spare control arm.
Enter the way too complicated solution:
Send-Cut-Send has a minimum order, so once we got their system to interpret my .DXF correctly (They use R12 .DXF... WTF?) they sent me 11 to fulfill minimum order cost.
And in action
I spread one trying to get the nut under the control arm tight. I guess it's good they sent me 11. I'm not sure there's room to make one that won't spread... maybe I'll play with it on a spare control arm.
-
- Posts: 617
- Joined: Thu May 20, 2010 10:07 pm
- Location: Grand-Mère, QC
Re: Storm Trooper Maintenance Thread
I have also used sendcutsend. I like them.
I had an issue (on my 84-87 Fiero) with Rodney Dickman zero-lash links whereby the ball-and-socket joints didn't have enough range of motion to work on my Fiero: I'm not sure what went wrong, but it's something to watch out for.
I had an issue (on my 84-87 Fiero) with Rodney Dickman zero-lash links whereby the ball-and-socket joints didn't have enough range of motion to work on my Fiero: I'm not sure what went wrong, but it's something to watch out for.
-
- Peer Mediator
- Posts: 15679
- Joined: Wed Nov 24, 2004 11:13 pm
- Location: In the darkness, where fear and knowing are one
- Contact:
Re: Storm Trooper Maintenance Thread
Is your sway bar upside down?
-
- Posts: 2960
- Joined: Mon May 24, 2010 5:34 pm
- Location: Aiken, SC
Re: Storm Trooper Maintenance Thread
it doesn't look like it to me, otherwise that hump would hit the steering rack right?
"I am not what you so glibly call to be a civilized man. I have broken with society for reasons which I alone am able to appreciate. I am therefore not subject to it's stupid laws, and I ask you to never allude to them in my presence again."
-
- Posts: 617
- Joined: Thu May 20, 2010 10:07 pm
- Location: Grand-Mère, QC
Re: Storm Trooper Maintenance Thread
Sendcutsend does have steel options which are stronger than mild steel. I don't know what you used.The Dark Side of Will wrote: ↑Sun Sep 03, 2023 8:10 pmI'm not sure there's room to make one that won't spread... maybe I'll play with it on a spare control arm.
********************************************************************************
I don't think my sway bar is upside down.
I followed the service manual which says to put the spade-shaped end of the sway bar on the left side of the car.
I sent an email asking Rodney about it. If this doesn't work out, I'll probably run rubber links for the time being.
-
- Peer Mediator
- Posts: 15679
- Joined: Wed Nov 24, 2004 11:13 pm
- Location: In the darkness, where fear and knowing are one
- Contact:
Re: Storm Trooper Maintenance Thread
That's why I asked... it does have a specific orientation. Funky. Is that before you lowered your control arm pivot?
-
- Peer Mediator
- Posts: 15679
- Joined: Wed Nov 24, 2004 11:13 pm
- Location: In the darkness, where fear and knowing are one
- Contact:
Re: Storm Trooper Maintenance Thread
Are you shocks installed in this photo? The UCA touching the crossmember is a drop limiter, but I thought the shock was a "higher" droop limiter.pmbrunelle wrote: ↑Sun Sep 03, 2023 10:35 pm I have also used sendcutsend. I like them.
I had an issue (on my 84-87 Fiero) with Rodney Dickman zero-lash links whereby the ball-and-socket joints didn't have enough range of motion to work on my Fiero:
RD endlink.jpg
I'm not sure what went wrong, but it's something to watch out for.
-
- Posts: 617
- Joined: Thu May 20, 2010 10:07 pm
- Location: Grand-Mère, QC
Re: Storm Trooper Maintenance Thread
I don't remember if the shocks were installed at that point, so I could recheck the endlinks with the shocks installed. If what you're saying is true, then there is a specific assembly order that must be followed to avoid damaging things.
Yes, the shock droop limiter is above the crossmember droop limiter.
I think the crossmember droop limiter serves to place the LCA at the correct position for shock installation. Since in service the crossmember droop limiter is not used, this allows the crossmember droop limiter to be built cheap/flimsy.
Yes, the shock droop limiter is above the crossmember droop limiter.
I think the crossmember droop limiter serves to place the LCA at the correct position for shock installation. Since in service the crossmember droop limiter is not used, this allows the crossmember droop limiter to be built cheap/flimsy.
-
- Peer Mediator
- Posts: 15679
- Joined: Wed Nov 24, 2004 11:13 pm
- Location: In the darkness, where fear and knowing are one
- Contact:
Re: Storm Trooper Maintenance Thread
I guess you mean install the shocks fully extended. With a little muscle, they can be R&R'd with the vehicle on the ground just by turning the wheels full lock.
-
- Posts: 617
- Joined: Thu May 20, 2010 10:07 pm
- Location: Grand-Mère, QC
Re: Storm Trooper Maintenance Thread
I was speaking in the context of installing the shock on the production line.The Dark Side of Will wrote: ↑Fri Sep 08, 2023 8:41 pm I guess you mean install the shocks fully extended. With a little muscle, they can be R&R'd with the vehicle on the ground just by turning the wheels full lock.
-
- Peer Mediator
- Posts: 15679
- Joined: Wed Nov 24, 2004 11:13 pm
- Location: In the darkness, where fear and knowing are one
- Contact:
Re: Storm Trooper Maintenance Thread
That's what I inferred. Then using production tooling to drive the upper mount bolts then pulls the suspension up to the shock's droop limit. Good observation.pmbrunelle wrote: ↑Sat Sep 09, 2023 3:42 pmI was speaking in the context of installing the shock on the production line.The Dark Side of Will wrote: ↑Fri Sep 08, 2023 8:41 pm I guess you mean install the shocks fully extended. With a little muscle, they can be R&R'd with the vehicle on the ground just by turning the wheels full lock.