Real Fiero Tech

Motor has new lifters and new rocker bolts. New lim gasket (zzp aluminum)


https://m.youtube.com/watch?v=Bey-pFjLjK4&feature

I didn't know about that one to two revolutions at a time going around . I prob did tighten it down a bit uneven but knowing it was the pressure plate springs is a relief. And thanks about the spinning the axle bit. I was told that if I spin both axles I the same direction at the same time it would ...

I was hearing a ticking or clicking sound when I was tightening down the pressure plate, even before I torqued the bolts. I sure hope I don't have to take this apart again. Any ideas Im worried that it may have been the rivets holding the Center disk to the clutch plate that broke. When I spin the a...

Bumping before engine goes to scrap yard. I also have a nice engraved upper plenum, A grey dash, and other parts so hit me up if you need something. Make offers on prices.

Thanks Shaun thats basically how I did it. Except I lowered the engine trans combo onto the engine trans mints that I base already put in the cradle. All together now. Now just to progress with harness and fuel lines and Coolant lines and brakes and batt cables, etc.

Shaun where are you located? I have a block and a complete motor sans fuel rail and egr crap.
You can take it if you like, nobody seems to want parts off it.
I am on Long Island in NY if that's close to you at all.

I have the motor on a stand, the 4spd tranny on a tire in the drive way, the spindles are separated from the tranny, and everything is off the cradle because I bought a newer condition cradle. I just mounted new tranny and motor mounts to the cradle. What is the sequence of putting these components ...

I am not sure what you mean by ripping off your vendor page. There are many people selling. The braided trans sport fuel lines on Old Europe. Some people include the compression fittings already on. I may try to flare brake tubing and the steel tubing on my braided lines and connect them via flared ...

I need to replace the stock v6 fuel lines on my 85 GT to make the stainless braided lines work for my 3800sc swap. I cut the oem lines too low and now I need to replace them. I was trying to fit on the stainless braided trans sport lines for my 3800 swap and I cut the OEM lines below the rubber hosi...

For sale : 1985 V6 4spd ECM. Ran great when pulled.

Make an offer via PM.

Hey I'd surely take another canister if it was free. The main reason I am keeping the stock canister is because I just bought a k/n filter for it. And even shipping is gonna cost Me at least 10-15 bucks. Ill keep up my search for the gasket and if I can't locate it ill just use the one I have or try...

Once the gasket is In and the air tube is on that's the end of it. My gasket isn't in TERRIBLE condition , I am just looking for one while I have everything apart.

I really don't want to pay for an air filter canister.

I tried but I got the file is too large error. It's a photo on my iPhone. I don't know why it would be too big to up load.Yeah it's at least a mg file but the max here is 256 kb.
If you send me your email I can email you the pic.

I have a photo of what I am referring to I just can't figure out how to post a picture here.

I have an 85 GT and the air filter canister has a ring gasket that's like a thick foam rubber rubber band that goes around the "outlet" snout where the rubber tube fits on (the tube that goes to the throttle body). I asked Rodney Dickman and he says his 88 didnt have that and I noticed tha...

I know this is highly improbable but if anyone needs any parts off a stock 2.8 v6, I am parting one out while doing a 3800sc swap.
Email me at mrlduet@yahoo.com if interested in any engine parts.

Shit, I just ordered the GM flywheel bolts. What are you torquing the hardware store bolts to?

I bought a flywheel from a highly regarded member on Old Europe and although I've been advised to use the arp Chevy cam bolts , they are about 1/8 inch too short and if I screw one of the arp cam bolts into the crank by hand without the flywheel on it, if its screwed in all the way it can go it feel...

I bought this gates one on eBay for 42.00 new http://m.ebay.com/orderDetails?itemId=141481734738&txnId=1064884376004 Rock auto said that was the part number. Man I hope it's correct. Now ill just need the bolt to hold it onto the bracket any info on that? And thank you so much for all the helpfu...

I did buy that guys bracket. I was looking at that tensioner too, but is that a good price ?