Search found 6866 matches
- Thu Dec 28, 2023 4:18 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 rotating assembly weights
- Replies: 25
- Views: 7296
Re: Lz9 rotating assembly weights
Cutting (grinding) the crank would not change the piston compression height. Offset grinding the crank like Upson did would change the required piston compression height. I guess Ti rods for a 4.3 V6 would be too expensive as there are no factory take-outs to snag used. Don't the LZ4/9 use the same...
- Thu Dec 28, 2023 11:28 am
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 rotating assembly weights
- Replies: 25
- Views: 7296
Re: Lz9 rotating assembly weights
So the big end would need to be narrowed like a typical SBC rod when converting to our engines as the LS engines have a similar rod width to the old sbc rod It seems that the coating comes off the rods at the big end, since that's where the rods in a stock V8 application share a rod journal, so they...
- Mon Dec 25, 2023 1:24 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 rotating assembly weights
- Replies: 25
- Views: 7296
Re: Lz9 rotating assembly weights
Ls7 also uses a Ti rod but it's listed at 6.067. Weight is similar to ls9 rod. With a 3.9 crank, ls7 rod, you would need a compression height of about 1.1. And whattaya know. It exists! Several dishes exist. I found a 16cc which is about 11.7 CR and a 26cc dish for about a 10.2 CR. 600 for forged pi...
- Mon Dec 25, 2023 12:03 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 rotating assembly weights
- Replies: 25
- Views: 7296
Re: Lz9 rotating assembly weights
Expensive proposition but I wanted to get the info in writing so I don't forget about it. Ls9 Ti rod info. Wrist Pin Dia. 0.984 Weight 452-482g Length. 5.99 Big end dia. 2.225 Lz9 has pin dia of .945 and a big end of 2.375. So the ls9 small end can be bushed I would assume, and maybe the big end bor...
- Thu Dec 21, 2023 5:57 pm
- Forum: Pontiac Fiero Discussion (General Non-Technical)
- Topic: progress on the banshee...
- Replies: 1264
- Views: 375545
- Wed Dec 20, 2023 8:03 am
- Forum: Technical Conversations on Pontiac Fieros
- Topic: LZ9 and LZ4 Fiero Swap Parts
- Replies: 16
- Views: 5314
Re: LZ9 and LZ4 Fiero Swap Parts
Do you have an LS style alt laying about. If not I have an ls4 one here
- Fri Dec 15, 2023 3:17 pm
- Forum: Pontiac Fiero Discussion (General Non-Technical)
- Topic: 1988 Fiero track car
- Replies: 80
- Views: 41679
Re: 1988 Fiero track car
Nice. Loving it
- Thu Dec 14, 2023 8:57 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Installing 3500, LZ4, for the time being
- Replies: 18
- Views: 11979
Re: Installing 3500, LZ4, for the time being
I pulled a datalog of a stock lz9 with the lnj stock cam, vs the 3.5 with the aftermarket cam. you can see the boost curves at the same rpm here. much less boost on the 3.5 clearly my turbo is oversized for the engine at lower rpm. the 3.5 needs more rpm to make up the difference which is to be expe...
- Sat Dec 09, 2023 8:55 pm
- Forum: Pontiac Fiero Discussion (General Non-Technical)
- Topic: sluppy123 aluminium front hubs
- Replies: 20
- Views: 13148
Re: sluppy123 aluminium front hubs
Curious as to what the factory hub runout is? Maybe it's already been mentioned
- Thu Dec 07, 2023 8:28 am
- Forum: Other Cars
- Topic: Northstar twin turbo into a Ford Fairlane.
- Replies: 1
- Views: 1969
- Wed Dec 06, 2023 9:21 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: High Feature V6 Swap
- Replies: 377
- Views: 100273
Re: High Feature V6 Swap
Exhaust is looking good. Welds look good from here
- Sat Dec 02, 2023 12:18 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 + 4 spd manual trans in 86 GT swap
- Replies: 55
- Views: 46399
Re: Lz9 + 4 spd manual trans in 86 GT swap
Looking good on that bracket.
Here is the current state of the engine. Lnj cam in, ready for some reassembly.
Here is the current state of the engine. Lnj cam in, ready for some reassembly.
- Thu Nov 30, 2023 2:46 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 + 4 spd manual trans in 86 GT swap
- Replies: 55
- Views: 46399
Re: Lz9 + 4 spd manual trans in 86 GT swap
It seems the camshaft is discontinued from gmparts direct.
I used the 2009 equinox lt trim which should be the 3.4
Welp. That's that I guess. No more available.
I used the 2009 equinox lt trim which should be the 3.4
Welp. That's that I guess. No more available.
- Wed Nov 29, 2023 11:08 am
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 + 4 spd manual trans in 86 GT swap
- Replies: 55
- Views: 46399
Re: Lz9 + 4 spd manual trans in 86 GT swap
You asked why not keep the vvt. I show why, and you say "so".
Hey man, when you do your 3.9 on the stormtrooper you can spend hours tuning your vvt cam for an extra 400 of additional rpm.
Hey man, when you do your 3.9 on the stormtrooper you can spend hours tuning your vvt cam for an extra 400 of additional rpm.
- Wed Nov 29, 2023 10:03 am
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 + 4 spd manual trans in 86 GT swap
- Replies: 55
- Views: 46399
Re: Lz9 + 4 spd manual trans in 86 GT swap
J upson who knew his vvt cam was not dialed in correctly but dynod anyways just to show what can happen. This was a gtech style road Dyno. Drastic power drop.
- Wed Nov 29, 2023 8:51 am
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 + 4 spd manual trans in 86 GT swap
- Replies: 55
- Views: 46399
Re: Lz9 + 4 spd manual trans in 86 GT swap
It's gonna run a microsquirt amp. Vvt is being deleted for simplicity of swap I have yet to see anyone who kept vvt with an micro or megasquirt do a Dyno to see where their power peaks. However j upon did dynod his with his modified vvt and it wasn't dialed in correctly. I believe power fell off bef...
- Tue Nov 28, 2023 3:02 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 + 4 spd manual trans in 86 GT swap
- Replies: 55
- Views: 46399
Re: Lz9 + 4 spd manual trans in 86 GT swap
Are the block casting numbers different? It doesn't look like there's enough iron to move that bolt hole outboard 4mm The earlier blocks have the bolt pattern the same as the 2.8. there is no need to move the bolt hole out further Eric is saying the lz9 is out a bit further. But it's close enough w...
- Mon Nov 27, 2023 9:36 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 + 4 spd manual trans in 86 GT swap
- Replies: 55
- Views: 46399
Re: Lz9 + 4 spd manual trans in 86 GT swap
Got the intakes, valve covers and pushrods out. Still need to remove timing assembly and lifters, then the lnj cam can go in
- Sun Nov 26, 2023 8:48 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 + 4 spd manual trans in 86 GT swap
- Replies: 55
- Views: 46399
Re: Lz9 + 4 spd manual trans in 86 GT swap
Interesting idea on the mount. We could do a test fit and give feedback if you want and take some pics.
I've got the front torn off and prepping for the lgd cam swap.
I've got the front torn off and prepping for the lgd cam swap.
- Sun Nov 19, 2023 7:40 pm
- Forum: Technical Conversations on Pontiac Fieros
- Topic: Lz9 + 4 spd manual trans in 86 GT swap
- Replies: 55
- Views: 46399
Re: Lz9 + 4 spd manual trans in 86 GT swap
The water manifold is one piece but it's separate from the timing cover.The Dark Side of Will wrote: ↑Fri Nov 17, 2023 2:39 pm I thought the 3900 had the upper water manifold at the back. I guess I was wrong about that.
Are the water manifolds two separate pieces or one large cover as with the Gen II & III engines?