Page 6 of 6
Re: mrsleeve91's DOHC build thread
Posted: Sat Jan 30, 2010 2:05 am
by mrsleeve91
Well I just found / installed a set of 60lb inj.s that have a very similar spray patter to the stockers.
Now I just need to put the intake on and powder coat the new t-housing, and put on the exhaust and I should be ready for take two!
Wish me luck! lol
Re:
Posted: Sat Jan 30, 2010 12:35 pm
by Emc209i
mrsleeve91 wrote:Well im expecting 600hp+ but 800 doesnt seem impossible. Iknow Ineed
to step up the inj. just been seeing what it can do..
Gonna need a slightly larger injector for 800. Just read over this thread again... and of course it goes without saying, but you've done a fantastic job. Can't wait for video.
Re: mrsleeve91's DOHC build thread
Posted: Sun Jan 31, 2010 4:25 pm
by fieromadman
Sounds like this should be entertaining!
Re: mrsleeve91's DOHC build thread
Posted: Mon Sep 15, 2014 8:07 pm
by Series8217
Bump for dyno charts!
Re: mrsleeve91's DOHC build thread
Posted: Mon Sep 15, 2014 8:55 pm
by Shaun41178(2)
does someone know something the rest don't? I figured this was dead and was actually thinking about this build yesterday
Re: mrsleeve91's DOHC build thread
Posted: Thu Sep 25, 2014 2:16 am
by mrsleeve91
It lives.
Re: mrsleeve91's DOHC build thread
Posted: Thu Sep 25, 2014 4:50 pm
by Emc209i
Numbers?
Re: mrsleeve91's DOHC build thread
Posted: Sun Nov 23, 2014 2:17 pm
by ericjon262
Bump for
Emc209i wrote:Numbers?
!
Re: mrsleeve91's DOHC build thread
Posted: Mon Dec 01, 2014 9:46 am
by Gambler87
Mrsleeve91 was wondering if u could pm me about the headers I talked to u about on 60degree
Re: mrsleeve91's DOHC build thread
Posted: Mon Dec 01, 2014 1:19 pm
by draven
Gambler87 wrote:Mrsleeve91 was wondering if u could pm me about the headers I talked to u about on 60degree
Ditto
Re: mrsleeve91's DOHC build thread
Posted: Wed May 20, 2015 12:03 pm
by Shaun41178(2)
from email correspondence.
410hp 378lb on 8.7 psi and my crappy 42lb inj.
I just received my 65lb bosh inj. And a sheet metal short runner intake is in the works.
I'm planning on hitting the dyno again this summer with my new upgrades and 18psi.
Re: mrsleeve91's DOHC build thread
Posted: Fri May 22, 2015 7:00 pm
by Emc209i
Relay to him via email:
"Turn the boost up to 15 lbs and see if the engine lasts."
Re: mrsleeve91's DOHC build thread
Posted: Sat May 23, 2015 7:00 am
by draven
Emc209i wrote:Relay to him via email:
"Turn the boost up to 15 lbs and see if the engine lasts."
Dude you have a hard-on for railing on the LQ1... however, even Matt Hawkins turbo'd properly tuned LQ1 eventually suffered a disintegrating timing chain tensioner after 60K and FerrariFan's GT30 LQ1 wasted a con rod bearing after boosting to 17psi without retuning..
Given MrSleeves all out build I wonder where the next failure point will be...
<edit = tensioner not timing chain failed>
Re: mrsleeve91's DOHC build thread
Posted: Mon May 25, 2015 4:43 pm
by Emc209i
You see a trend, eh?
