Real Fiero Tech

This is as complete as it gets. I have the complete uncut harness, all accessories, fuse box, fuel pump, exhaust all the way to the joint just after the cat, drive by wire gas pedal, two PCMs: one for the tranny and one for the motor, Mass airflow sensor. This motor will bolt right to the six speed in the SAAb 9-3(six speed), and will work out quite nice in a Fiero.

I am asking 1500.oo for all of it.

Wow, awesome price.

I have this engine in my CTS, it hauls ass in a big car. Someone buy this and get Darth to swap it in. Would be a wicked fiero engine.

They are rated at 255hp fron GM and run on regular fuel. The Caddy forum guys have shown that they respond well to intake and exhaust mods. I don't doubt that this engine can get close to 280hp uncorked and less accessories.

I have also spoken to a few tuning companies, and this can be made to run in a Fiero with the stock PCM with drive by wire or without, for about 400.oo.

I had a rental saturn with that engine. it has balls. After driving it for a week, I'm thinking about using one of them instead of a N*.

last time motor and harness with ecm for 1000.oo

How many miles are on the engine?

Let me try to find a Fiero to put it in...

motor has 17,000 miles on it.

Can you put up a bunch of pictures of what's all included?

What engine sensors, or components, are not included?

Thanks

I decided to sell the engine harness and ecm. all the sensors are still on the motor. I can email you pictures. I havent taken the time to set up an online picture hosting account yet.

The reason I lowered the price this much is because you wont be getting everything like I wzas offering before. I have the electronic throttle as the motor is drive by wire, the fuel pump and complete fuel lines, 75% of the exhaust, the A/C compressor and lines, power steering pump and lines, alternator, most of the body harness, tranny ecm, mount, and a few more things I cant think of right off the top of my head.

So what do I get, and what don't I get?

You list all of that, but didn't say if it was included or not.

I thought you sold the harness and ECM?

XzotikGT wrote:I decided to sell the engine harness and ecm.

I am interested, but only if I get everything that was listed in your original post.

I don't need the fuel pump, any of the A/C or power steering shit, body harness, tranny ECM, or the exhaust.

I do need the engine harness and ECM, engine side of the fuel lines, everything associated with the drive by wire system (Pedal, wires, and throttle body), the exhaust manifolds and crossover, and the alternator. And also, I want some pics if you can. Basically, I need everything needed to do an engine swap in a Fiero. Because I don't want to go eBay and junkyard shopping for shit. And if I'm going to have to do that, then $1000 is just too much.

sounds good to me, whats your email?

AaronZ34@gmail.com

Thanks dude

sending a few pictures now.

No problem.

Hey, I wanna see what the new 3.6 looks like.

Here they are. I am still completely torn as to whether I should buy this or not. It is a big step over my motor, however all of my work would be wasted. Which I don't mind, as I really enjoy doing that work, but I don't want to lose too much money on the deal. I think I'll see how much I can get for my powertrain, then I'll look into this.

possible trade?

Let's take this to PMs.

this thing looks nearly as big as my 5.3! And it has as much power, if not as much potential. Then again, 12 psi at the TB should give 540 HP.

check this out for potential

http://www.peters-racing.com/engine-new/