Real Fiero Tech

Got a idea and want to run it by to see what you all think. I have a 7730 ECM and my trans is compatible to it, But not the Fiero speedo.(of course you know that) What im thinking and this may have been went over before but im wanting to use the speedo pod from the donor car in the Fiero cluster. Am...

Yes. Thats what I have on my 86. They fit great! 225/40/18 fronts 245/40/18 rears.

Are you sure you abuse your car enough to warrant a cooler? Oh yess!! I will be using the full benefit of this cooler. I have a TGP 3.1 with a t3. turbos make for lots of heat in the oil so its needed. Im thinking water to oil to get the oil up to temp then air to oil after to not get to hot. idk j...

I never thought of it that way. Thanks :salute:

I got a RX7 oil cooler from the J-yard and was thinking of a good place to pit it. Well the only good place is were it belongs, UP FRONT. This makes for a long oiling system. about 12 extra foot. :scratch: Think if run 1/2" hard line I can get away with It? I know it will drop psi but don't kno...

Why'd someone bother sticking the Volvo turbo on there? It's too small.. I think its about the same size or smaller than the stock TGP turbo, isnt it?[/quote] Idk you tell m e. There both garrett. The t3(volvo) is A/R 52 c. and A/R 48 e. the t2(tgp) is A/R 80 c. and A/R 68 e. http://img213.imageshac...

90 TGP 3.1 Custom many and a t3 off a vovol 740.:thumbleft:

Were can I fined more Fiero related info on the 3.1 TGP swap? I know other people have done this but I cant fined any thread's on them! The swap is pretty straight forward from what I can tell I'm just looking for the technical things like weiring and ECM control. Is it like the 3.4 DOHC swap? If yo...

Well it's just a thought. thanks for posting your thoughts about it :thumbleft:

I was watching the HP TV seg. that fidenza has on there site. The one were thay put on the remote mount turbo setup. They say there's only a 1 psi lose with all that piping and it makes the intercooler 90% efficient! That makes good sense. Oh and thay ran the MAS after the turbo with no bad effects ...

Tack Filter :thumbleft: Little thing with two white wire's and a white plug. It's just behind the coil.

No. Well yes... But No.. The seat if 9" at the highest point. The bottom of the seat is Like 2" from the floor. It will Set gust like a Fiero seat.

Oh Im 5'9" and 150lb.

Bottom- 21" W / 22" L
Top- 20"W / 30"H
Seat sites 9" at highest point off floor. This seat is perfectly fit for a Fiero. :thumbleft:

Will, Do you have a Link or Add. handy for RCC? Thank's

'84 - '87 Fiero Steel Drop / Lowering Spindles / Knuckles / Hubs $799 / pr. with bearings, seals and studs pre-installed http://www.streetdreamsbyross.com/gr/alumknck.jpg Man this is just about what im looking for but the $800. Is a little much. They don't sell just the hub's because thay say that t...

Any one ever tried to put these seats in there Fiero? I mean there every were. They came in the Eclipse,Talon,Avenger,Seabring,3000 GT, and the Stealth! So this is a common fined. Tell me what you think. http://img405.imageshack.us/img405/9530/jakescar007ef5.th.jpg http://img71.imageshack.us/img71/3...

Is there a hub or spindle that I can swap to get a 5-4.50 / 114.3mm bolt pattern for the 84-87 front's? Even if its from a different manufacture and I'll need to do a little fab work that's fine. I just need something close to start with, but I've Had NO luck finding ANYTHING. So if you can... PLEAS...

I've read this on NICO and on a Supra forum! I think it's been proven time and time again. It's one of the upgrades on my list :thumbleft:

No I dont think it is. I dont think any GM motor is....

Pyrthian wrote:ever notice that the best setups also look good?

I don't know..... Mike Smiths DOHC upper intake look's like a Shit but it works vary well.